Improve Productivity and Safety with Kyotechs 1211 Excavator Monitor

There are usually the highest and lowest oil level marks (MAX and MIN) on the inner wall of the oil filling port of each engine. This means that the oil level cannot exceed MAX or be lower than MIN.

A lower oil level, that is, a decrease in the amount of oil in the engine, will increase the oil load, causing the oil to become more seriously contaminated by heat, which not only weakens the lubrication performance, but also increases the fuel consumption. Because the less oil in the engine, the higher the oil temperature; and the higher the oil temperature, the greater the fuel consumption will be as the oil temperature rises. It is very dangerous to run the engine when the oil level is at the lowest point (MIN).

Keeping the oil level at the highest point (MAX) all the time will cause the oil to foam and lead to insufficient lubrication, resulting in serious wear. Foaming oil will also increase fuel consumption.

Therefore, it is recommended to keep the engine oil level between the MAX and MIN marks at a position close to one-third of the MAX.

1.There is no oil in the fuel tank.

2.The fuel filter and oil-water separator are blocked.

3.The low-pressure oil circuit does not supply oil.

4.The injection pump does not pump oil.

5.There is air in the oil circuit.

6.The valve timing is misaligned. The opening time of the valve is not coordinated with the stroke of the piston in the cylinder. For example, when the piston makes a compression stroke in the cylinder, the intake and exhaust valves are open, and fresh air is driven out of the cylinder, so that there is no combustion gas in the cylinder and it cannot start.

7.The solenoid valve of the injection pump is broken and is in a closed state, and the diesel cannot enter the high-pressure chamber.

1. Kyotechs, Focus on the machinery industry over 20 years, have abundant experience and sound reputation in the field. support the full range of excavator accessories.
2. kyotechs offer Maintenance service: repair and testing for monitor ECU controller software; Engine start testing, remanufacture and repaint; Hydraulic pump refit, etc.
3. 100% quality guaranteed; Kyotechs offers different quality requirements for excavator parts. new and used genuine parts, OEM parts made in China, Japan, Korea. main parts normal operation running at least 3-5 years. Use Kyotechs parts; few worries!
4. Small orders and sample orders are acceptable; large quantities and price negotiations.
5. Quick delivery time: order before 4:00 p.m. and ship out on the same day.

Check the battery charge and connections, inspect the starter motor and ignition system, ensure the fuel system is supplying fuel properly, and read fault codes for further diagnostics.

Kobelco excavator maintenance tips 1: Cooling to prevent air blockage In high temperatures in summer, the engine is prone to air blockage due to high speed and difficult heat dissipation, which makes it difficult to start the engine after stopping for a few minutes. Once air blockage occurs, the excavator driver should stop the engine immediately to cool down and eliminate the fault.

Kobelco excavator maintenance tips 2: Observe the water temperature gauge at any time to prevent water shortage When driving in high temperature weather, always pay attention to checking the cooling water volume and the water temperature gauge. When water shortage is found, immediately idle the engine to cool down before adding water, and be careful not to open the radiator cap immediately to prevent burns.

Kobelco excavator maintenance tips 3: Prevent engine oil from deterioration Lubricating oil is easily diluted by heat, resulting in poor oxidation resistance, easy deterioration, and even causing faults such as burning of the bearing and the shaft. Therefore, the crankcase and gearbox should be replaced with summer lubricating oil, and the amount and quality of the lubricating oil should be checked frequently, and replaced in time.

Kobelco excavator summer maintenance tips 4: timely cleaning of engine surface oil If the external oil of the engine is too thick, it will affect the heat dissipation and bury the hidden danger of failure of various parts. You can use the high-pressure spray method to clean the engine parts with a cleaning agent that does not corrode the body parts.

Kobelco excavator summer maintenance tips 5: prevent the water tank water temperature from being too high In summer, the cooling water of Kobelco excavators evaporates and consumes quickly. You must add enough cooling water before leaving the vehicle, and check the water level frequently during work. For single-cylinder diesel engines without a water temperature gauge, always pay attention to the red mark height of the water tank float. If the float cannot be used normally, it should be repaired in time. If the boiling phenomenon occurs during work, do not add cooling water directly. Stop the work, slow down the generator, and slowly add cooling water after the water temperature drops to avoid cracks in the water tank when it is cold.

Kobelco excavator summer maintenance tips 6: Ensure the best oil supply time In summer, the oil supply time of Kobelco excavators should be adjusted. If the oil is supplied too early, the engine will make a knocking sound and sometimes reverse; the oil supply time should not be too late, otherwise the engine will work weakly.