The Ultimate Guide to the Kyotechs 9514TNV98 Engine Assy: Everything You Need to Know

1. Kyotechs, Focus on the machinery industry over 20 years, have abundant experience and sound reputation in the field. support the full range of excavator accessories.
2. kyotechs offer Maintenance service: repair and testing for monitor ECU controller software; Engine start testing, remanufacture and repaint; Hydraulic pump refit, etc.
3. 100% quality guaranteed; Kyotechs offers different quality requirements for excavator parts. new and used genuine parts, OEM parts made in China, Japan, Korea. main parts normal operation running at least 3-5 years. Use Kyotechs parts; few worries!
4. Small orders and sample orders are acceptable; large quantities and price negotiations.
5. Quick delivery time: order before 4:00 p.m. and ship out on the same day.

Regularly check the battery voltage, electrolyte level and connection status to ensure the normal operation of the battery.

Reasons from the piston group
1. The piston ring gap is too small. If the opening gap, side gap or back gap of the piston ring is too small, the piston ring will be stuck due to heat expansion when the engine is working, and it will be pressed tightly against the cylinder wall, or the piston ring will be broken, which can easily pull out grooves on the cylinder wall.
2. The piston pin is out. Because the piston pin retaining ring is not installed or falls off or breaks, the piston pin will be out during movement, which can easily damage the inner wall of the cylinder and cause the cylinder to blow into the crankcase.
3. The piston cylinder gap is too small or too large. If the piston material is poor, the manufacturing size error is too large, or the piston is deformed after the piston pin is assembled, the matching gap between the piston and the cylinder is too small, and the piston is stuck after heat expansion, which will then damage the cylinder wall.
4. The piston ring is seriously carbonized. Excessive carbon deposits cause the piston ring to stick or bite in the ring groove. At the same time, carbon deposits are a hard abrasive that will grind into longitudinal grooves on the cylinder wall.
5. The piston is seriously off-cylinder. Due to the bending and twisting of the connecting rod, the parallelism and coaxiality deviations of the connecting rod journal, main journal, and piston pin seat are too large, causing the piston to be significantly off-cylinder, which will accelerate the wear of the piston ring, piston and cylinder wall and destroy the formation of the oil film.

Reasons for cylinder sleeves
1. The roundness and cylindricality tolerances of the cylinder sleeves exceed the allowable range, which greatly reduces the sealing of the piston and cylinder sleeves. The high-temperature gas in the cylinder flows down, destroying the oil film between the piston and the cylinder wall, and then causing cylinder pulling.
2. The cylinder sleeve is deformed during the assembly process. For example: the protrusion of the upper end surface of the cylinder sleeve is too large, and the cylinder sleeve is deformed after the cylinder head is installed; the cylinder sleeve water blocking ring is too thick, and the cylinder sleeve is deformed after being pressed into the body, which can easily cause cylinder pulling.

Reasons for use:
1. Whether the size of the cylinder sleeve used during assembly does not match the cylinder body and piston.
2. The air filter is not sealed, which makes the filtering effect worse. Dust, sand and other impurities in the air are sucked into the cylinder, forming abrasive wear. Tests show that if a few grams of dust are sucked in every day, the wear of the cylinder liner will increase by more than 10 times.

Abnormal noise may be caused by air entering the system, cavitation, internal component wear or hydraulic oil contamination.

After the newly purchased battery is injected with the liquid with the appropriate specific gravity, it should be placed for 6-8 hours to allow the liquid to penetrate the plates. When the temperature of the liquid drops below 30℃, it can be charged for the first time. The initial charge should be carried out in two stages. The charging current in the first stage should be lower than 1/10 (one tenth) of the rated capacity of the battery, and the time is about 25-35 hours. When the voltage of a single cell rises to 2.4 volts, the current is reduced by half and the second stage is entered, which takes about 20-30 hours. When the electrolyte emits strong bubbles and the specific gravity no longer rises, the voltage of a single cell rises to 2.6-2.75 volts and remains unchanged for 2-3 hours, it means that the battery is fully charged. During charging, the temperature of the electrolyte will rise, exceeding 40℃ in summer and 35℃ in winter. Charging should be suspended and recharged when the temperature drops below 30℃ to prevent damage to the plates and separators.