Upgrade Your Engine with Kyotechs 936J05E Piston: The Ultimate Guide

1. There must be enough starting speed. The high starting speed means less gas leakage in the cylinder, shorter heat transfer time of compressed air to the cylinder wall, less heat loss, and higher gas temperature and pressure at the end of compression. Generally, the speed is required to be above 100r/min.

2. The cylinder should have good sealing. This can further reduce the amount of leakage and ensure that the gas has sufficient combustion temperature and pressure at the end of compression. The compression pressure of the cylinder shall not be lower than 8_0_%_ of the standard value.

3. The engine is required to have appropriate clearance relative to the running parts and good lubrication.

4. The battery must have sufficient starting capacity and the technical condition of the starting circuit is normal.

5. The starting oil volume meets the requirements, the injection quality is good, and the injection advance angle meets the requirements.

6. Use fuel that meets the requirements

1. Chain off caused by tension cylinder failure
At this time, you should check whether you have forgotten to butter the tension cylinder and see if there is any oil leakage in the tension cylinder.

2. Chain off caused by severe wear of the crawler
If used for a long time, the crawler will definitely be worn, and the wear of the chain ribs, chain barrels and other parts on the crawler will also cause the crawler chain off.

3. Chain off caused by wear of the chain guard
Now almost all excavator crawlers have chain guards, and chain guards can play a very important role in preventing chain off, so it is also very important to check whether the chain guard is worn.

4. Chain off caused by wear of the drive motor ring gear
For the drive motor ring gear, if it is severely worn, we need to replace it, which is also an important reason for the excavator chain off.

5. Chain off caused by damage to the sprocket wheel
Generally speaking, oil leakage of the sprocket wheel oil seal of the excavator will cause severe wear of the sprocket wheel, which will cause the crawler chain off. The public account Zhizao Daguan focuses on sharing relevant theoretical knowledge in the engineering machinery manufacturing industry.

6. Chain derailment caused by guide wheel damage
When checking the track guide wheel, check whether the screws on the guide wheel are missing or broken. Check whether the groove of the guide wheel is deformed.

Usually the coolant is changed every two years or as recommended by the manufacturer.

The pump housing will wear more in the oil inlet chamber. If the pump housing is symmetrical, it can be turned 180 degrees. Then use it. For the passive gear, the two ends cannot be replaced. Make a mark when removing it. Because the gear will wear on one side. The active gear is integrated with the rotating shaft and cannot be turned over; turning the passive gear over can change the contact point of the meshing line of the two gears. After the pump is assembled, add a little lubricating oil and rotate it slightly by hand. The feel should be smooth.

In the field of modern engineering machinery, excavators play a vital role, and behind this, there is a company that is quietly adding momentum to the industry, that is Kyotechs. With the mission of "building a community of shared destiny for partners and adding strength to the excavator industry", Kyotechs is not only committed to providing high-quality excavator parts, but also promoting the development of the entire industry with a long-term vision and innovative thinking.

In an increasingly competitive market environment, the era of fighting alone is over, and win-win cooperation is the key to future development. Therefore, the company has always been committed to building a close community of shared destiny for partners. This is not just a simple business cooperation, but also a deep collaboration based on trust, mutual assistance and common goals.

In this community of shared destiny, Kyotechs shares information, resources and opportunities with suppliers, customers, technical partners and other relevant parties. In this way, the company can not only respond quickly to market needs, but also foresee and respond to industry challenges in advance. The success of our partners is our success. It is this concept of symbiosis and win-win that has established a good reputation for Kyotechs in the industry.

As a company focusing on excavator parts, Kyotechs' products cover hydraulic pumps, engine parts, electronic controllers, transmission system parts and other fields. These high-quality parts not only ensure the efficient operation of the excavator, but also play an important role in improving overall engineering efficiency and reducing equipment failures.

Kyotechs not only pursues commercial success, but also takes "becoming a happy person in the field of excavation equipment" as its vision, emphasizing the happiness and satisfaction of all stakeholders. This vision reflects the company's deep care for employees, customers and society.

For Kyotechs, customer satisfaction is an important criterion for measuring our success. The company has always been customer-oriented and provides high-quality products and a full range of services. Whether it is product quality, delivery speed or after-sales service, Kyotechs strives to do its best to ensure that every customer can enjoy an experience beyond expectations.